GOST 1759.0-1987
Болты, винты, шпильки и гайки. Технические условия
螺栓 螺丝 螺柱和螺母 规格
BS ISO 8992-2005
Fasteners. General requirements for bolts, screws, studs and nuts
紧固件 螺栓、螺钉、螺柱和螺母的一般要求
2005-04-27
KS B ISO 8992(2020 Confirm)
파스너－볼트, 스크루, 스터드 및 너트에 대한 일반 요구 사항
紧固件螺栓、螺钉、螺柱和螺母的一般要求
2005-12-20
SAE J1061_201211
Surface Discontinuities on General Application Bolts, Screws, and Studs
一般应用螺栓 螺钉和螺柱的表面不连续性
2012-11-19
GOST ISO 8992-2015
Изделия крепежные. Общие требования для болтов, винтов, шпилек и гаек
紧固件 螺栓 螺钉 螺柱和螺母的一般要求
2015-09-29
GB/T 16938-2008
紧固件 螺栓、螺钉、螺柱和螺母 通用技术条件
Fasteners - General requirements for bolts,screws,studs and nuts
2008-08-25
ISO 8992-2005
Fasteners — General requirements for bolts, screws, studs and nuts
紧固件——螺栓、螺钉、螺柱和螺母的一般要求
2005-04-15
BS 2693-1-1956
Specification for screwed studs-General purpose studs
螺纹螺柱规范 通用螺柱
1956-01-30
SAE AS3062D
Bolts, Screws, and Studs - Screw Thread Requirements
螺栓 螺丝和螺栓 螺纹要求
2019-02-13
JIS B 1009-1991
Bolts, screws and studs -- Nominal lengths, and thread lengths for general purpose bolts
螺栓、螺钉和螺柱通用螺栓的公称长度和螺纹长度
1991-01-01
KS B 1065(2020 Confirm)
수나사 부품－호칭 길이 및볼트의 나사부 길이
螺栓 螺钉和螺柱-公称长度andthread一般用途螺栓长度
2015-12-31
BS EN 26157-1-1992
Fasteners. Surface discontinuities. Bolts, screws and studs for general requirements
紧固件 表面不连续 一般要求用螺栓、螺钉和螺柱
1992-05-01
GB/T 5779.1-2000
紧固件表面缺陷 螺栓、螺钉和螺柱 一般要求
Fasteners--Surface discontinuities--Bolts，screws and studs for general requirements
2000-09-26
ASTM F468M-06(2018)
Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric)
通用六角带帽螺钉和螺柱用有色金属螺栓的标准规范（米制）
2018-09-01
ASME B18.2.8-1999(R2017)
Clearance Holes for Bolts, Screws, and Studs
螺栓、螺钉和螺柱的间隙孔
1999-01-01
ASTM F468-23
Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
一般用途有色金属螺栓、六角螺钉、内六角螺钉和双头螺栓的标准规范
2023-06-01
ISO 262-2023
ISO general purpose metric screw threads — Selected sizes for bolts, screws, studs and nuts
ISO通用公制螺纹-螺栓、螺钉、螺柱和螺母的选定尺寸
2023-04-20
UNE 17077-1980
SCREWS, BOLTS AND STUDS. THREAD RUN OUT.
螺钉、螺栓和螺柱 线用完了
1980-12-15
SAE AS3063C
Bolts, Screws, and Studs, Geometric Control Requirements
螺栓、螺钉和螺柱 几何控制要求
2019-02-26
GB/T 3103.1-2002
紧固件公差 螺栓、螺钉、螺柱和螺母
Tolerances for fasteners--Bolts，screws，studs and nuts
2002-12-05