SME MS910506
Advancements In Rim Equipment
Rim设备的进展
1991-06-01
MIL MIL-F-16377/40A Notice 1-Validation
FIXTURES, LIGHTING; LOCKS FLUORESCENT LAMP (SUPERSEDING MIL-F-16377/40)
灯具 灯具; LOCKS荧光灯（取代MIL-F-16377/40）
1989-06-22
SME EM910525
Rim--A Continuous Improvement--A Case Study Of Davidson Exterior Trim Textron
Rim——持续改进——戴维森车外装饰德事隆的案例研究
1991-06-01
SME CM97-141
Thin Wall Reaction Injection Molding (Tw-Rim) A Low Pressure Process For Rapid Prototyping
薄壁反应注射成型（Tw Rim）用于快速成型的低压工艺
1997-06-01
MIL AND10583B Notice 1-Validation
RIM CONTOUR-25.00-28, TYPE III, LOW PRESSURE, MAIN LANDING GEAR WHEEL (SUPERSEDING AND10583A)
RIM CONTOUR-25.00-28 TYPE III 低压 主轨道轮（SUPERSEDING AND10583A）
1988-10-31
MIL MIL-C-85144C
CONTROL SECTION, GUIDED MISSILE FOR AIM/RIM-7M, GUIDED MISSILE (SUPERSEDING MIL-C-85144B)
控制部分 用于AIM/RIM-7M的导弹 导弹（取代MIL-C-85144B）
1986-10-22
MIL MS28927A Notice 1-Cancellation
CLAMP-RIM, CLENCHING FOR MIL-R-8903 RESISTOR (SUPERSEDING MS28927) (NO S/S DOCUMENT)
MIL-R-8903电阻器的CLAMP-RIM（取代MS28927）（无S/S文件）
1998-09-30
MIL MS24369A Notice 1-Validation
RIM CONTOUR - 30X8.8, TYPE VII, EXTRA HIGH PRESSURE, MAIN LANDING GEAR WHEEL (SUPERSEDING MS24369)
RIM CONTOUR - 30X8.8 第七类 超高压 主轨道轮（取代MS24369）
1988-10-31
MIL AND10581C Notice 1-Validation
RIM CONTOUR-20 X 4.4, TYPE VII, EXTRA HIGH PRESSURE, LANDING GEAR WHEEL (SUPERSEDING AND10581B)
RIM CONTOUR-20 X 4.4 第七类 额外的高压 起重齿轮（取代和10581B）
1988-10-31
MIL MIL-STD-2093
RELIABILITY PROCEDURES FOR PRODUCTION OF GUIDANCE AND CONTROL SECTION FOR GUIDED MISSILE AIM/RIM-7M (NO S/S DOCUMENT)
导弹AIM/RIM-7M制导和控制部分生产的可靠性程序（无S/S文件）
1982-03-26
MIL MIL-R-26672A Notice 1-Validation
RIFLE,.22 HORNET AND.22 CALIBER LONG RIFLE RIM FIRE, SURVIVAL, TYPE MA-1 (SUPERSEDING MIL-R-26672)
RIFLE .22 HORNET和.22 CALIBER LONG RIFLE RIM FIRE SURVIVAL 型号MA-1（取代MIL-R-26672）
1989-09-05
MIL MS24368A Notice 1-Validation
RIM CONTOURS, 56 X 1 AND 49 X 17, TYPE VII, EXTRA HIGH PRESSURE, MLG WHEEL (SUPERSEDING MS24368)
RIM轮廓 56 X 1和49 X 17 第七类 超高压 MLG轮（取代MS24368）
1988-10-31
UNE 85402-1990
HARDWARE FOR LOCKS IN BUILDINGS. RIM DOOR LOCKS. TESTS.
建筑物锁的五金件 边缘门锁 测验
1990-06-01
UNE 85401-1990
HARDWARE FOR LOCKS IN BUILDINGS. RIM DOOR LOCKS. DEFINITIONS. SPECIFICATIONS.
建筑物锁的五金件 边缘门锁 定义 规格
1990-06-22
DIN 81307
Rim-locks with latch-bolt for hinged doors on ships
船用铰链门用带插销的轮辋锁
2003-08-01
DIN 81311
Rim-locks with latch-bolt for heavy hinged doors on ships
船用重型铰链门用带插销的轮辋锁
2005-05-01
MIL MS24370B Notice 1-Validation
RIM CONTOURS-24 X 5.5, 22 X 5.5, 20 X 5.5 AND 18 X 5.5, TYPE VII, EXTRA HIGH PRESSURE, LANDING GEAR WHEEL (SUPERSEDING MS24370A)
RIM CONTOURS-24 X 5.5,22 X 5.5,20 X 5.5和18 X 5.5 第七类 额外的高压 起重齿轮（取代MS24370A）
1988-10-31
DIN 81309
Rim-locks with latch-bolt for hinged doors of lavatory and bath on ships
船上厕所和浴室铰链门用带插销的轮缘锁
2003-08-01
DIN 81312
Rim-locks without latch bolt for heavy hinged doors on ships
船用重型铰链门用无插销轮辋锁
2019-03-01
DIN 81307-DRAFT
Draft Document - Rim-locks with latch-bolt for hinged doors on ships
文件草案.船上铰链门用带插销的轮辋锁
2002-03-01