GB/T 4909.12-2009
裸电线试验方法 第12部分：镀层可焊性试验-焊球法
Test methods for bare wires - Part 12: Solderability test of coating - Solder globule method
2009-03-19
SJ/T 10146-1991
焊槽法可焊性测试仪技术条件
Specification for solderability test instrument by solder bath method
1991-04-02
SJ/T 10145-1991
润湿称量法可焊性测试仪技术条件
Specification for solderability test instrument by wetting balance method
1991-04-02
BS EN ISO 12224-3-2003
Solder wire, solid and flux cored. Specification and test methods-Wetting balance test method for flux core solder wire efficacy
实心和药芯焊丝 规范和试验方法
2003-07-22
GB/T 41104.3-2021
实心和药芯软钎料丝 规范和试验方法 第3部分：药芯软钎料丝功效的润湿平衡试验方法
Solder wire, solid and flux cored—Specifications and test methods—Part 3:Wetting balance test method for flux cored solder wire efficacy
2021-12-31
GB/T 33087-2016
仪器分析用高纯水规格及试验方法
Ultra pure water for instrumental analysis specification and test methods
2016-10-13
BS EN ISO 12224-1-1998
Solder wire, solid and flux cored. Specification and test methods-Classification and performance requirements
实心和药芯焊丝 规范和试验方法
1998-09-15
BS EN ISO 12224-2-1999
Solder wire, solid and flux cored. Specification and test methods-Determination of flux content
实心和药芯焊丝 规范和试验方法
1999-05-15
BS 5772-6-1984
Specification for electromechanical components for electronic equipment: basic testing procedures and measuring methods-Climatic tests and soldering tests
电子设备用机电元件规范:基本试验程序和测量方法 气候试验和焊接试验
1984-11-30
UNE-EN ISO 12224-3-2004
Solder wire, solid and flux cored - Specifications and tests methods - Part 3: Wetting balance test method for flux cored solder wire efficacy (ISO 12224-3:2003)
实心和药芯焊丝规范和试验方法第3部分:药芯焊丝功效的润湿平衡试验方法
2004-01-16
DIN EN ISO 12224-3
Solder wire, solid and flux cored - Specifications and test methods - Part 3: Wetting balance test method for flux cored solder wire efficacy (ISO 12224-3:2003)
实心和药芯焊丝.规范和试验方法.第3部分:药芯焊丝功效的润湿平衡试验方法（ISO 12224-3-2003）；德文版EN ISO 12224-3:2003
2003-10-01
JJF 1372-2012
贯入式砂浆强度检测仪校准规范
Calibration Specification for Instrument of Testing Mortar-strength by Penetration Resistance Method
2012-12-12
GB/T 41104.2-2021
实心和药芯软钎料丝 规范和试验方法 第2部分：钎剂含量的测定
Solder wire, solid and flux cored—Specification and test methods—Part 2: Determination of flux content
2021-12-31
GB/T 41104.1-2021
实心和药芯软钎料丝 规范和试验方法 第1部分：分类和性能要求
Solder wire, solid and flux cored—Specification and test methods—Part 1: Classification and performance requirements
2021-12-31
ISO 12224-1-2024
Solder wire, solid and flux-cored — Specification and test methods — Part 1: Classification and performance requirements
实心和药芯焊丝规范和试验方法第1部分:分类和性能要求
2024-05-03
ISO 12224-2-2024
Solder wire, solid and flux-cored — Specification and test methods — Part 2: Determination of flux content
实心和药芯焊丝规范和试验方法第2部分:焊剂含量的测定
2024-05-03
KS B ISO 9211-4(2021 Confirm)
광학 및 광학 기기－광학 코팅－제4부：시험 방법
光学和光学仪器光学涂层第4部分:特殊试验方法
2016-11-28
KS B ISO 9211-4
광학 및 광학 기기－광학 코팅－제4부：시험 방법
光学和光学仪器光学涂层第4部分:特殊试验方法
2016-11-28
GOST R ISO 9211-4-2016
Оптика и оптические приборы. Покрытия оптические. Часть 4. Специальные методы испытаний
光学和光学仪器 光学涂料 具体测试方法
GOST 23923-1989
Средства измерений удельной активности радионуклида. Общие технические требования и методы испытаний
测量仪器的放射性核素比活度 一般技术要求和试验方法