JB/T 9186-1999
二氧化碳气体保护焊工艺规程
Welding procedure specification for CO2 shielded arc welding
1999-06-24
AWS B2.1.011-91
Standard Welding Procedure Specification for Shielded Metal Arc Welding of Galvanized Steel, 10 through 18 Gauge, in the As-Welded Condition, With of Without Backing
无背衬焊态10至18号镀锌钢的保护金属极电弧焊标准焊接工艺规范
1991-01-01
1A1W1S1 Archive Product 133
Standard Welding Procedure Specification (Swps) for Shielded Metal Arc Welding of Galvanized Steel (M-1), 10 through 18 Gauge, in the As-Welded Condition, with or without Backing
焊接状态下10至18号镀锌钢（M-1）带或不带衬垫的保护金属极电弧焊标准焊接工艺规范（Swps）
2002-01-01
AWS B2.1-1-233-2006
Standard Welding Procedure Specification (Swps) for Argon Plus 25% Carbon Dioxide Shielded Gas Metal Arc Welding (Short Circuting Transfer Mode) followed by Argon Plus 2% Oxygen Shielded Gas Metal Arc Welding (Spray Transfer Mode) of Carbon Steel (M-1/P-1/S-1) Groups 1 and 2, 1/8 through 1-1/2 inch
碳钢（M-1/P-1/S-1）组1和2、1/8至1-1/2英寸的氩加25%二氧化碳气体保护金属极弧焊（短路过渡模式）和氩加2%氧气保护气体保护金属极弧焊（喷射过渡模式）的标准焊接工艺规范（Swps）
2006-01-01
AWS B2.1-1-232-2006
Standard Welding Procedure Specification (Swps) for Argon Plus 25% Carbon Dioxide Shielded Gas Metal Arc Welding (Short Circuting Transfer Mode) followed by Argon Plus 25% Carbon Dioxide Shielded Flux Cored Arc Welding of Carbon Steel (M-1/P-1/S-1, Groups 1 and 2), 1/8 through 1-1/2 inch Thick, ER70
1/8至1-1/2英寸厚ER70碳钢（M-1/P-1/S-1 第1组和第2组）氩加25%二氧化碳保护气体保护金属弧焊（短路过渡模式）和氩加25%二氧化碳保护药芯焊丝电弧焊的标准焊接工艺规范（Swps）
2006-01-01
AWS B2.1.012-91
Standard Welding Procedure Specification for Shielded Metal Arc Welding of Carbon Steel, (M-1, Group 1), 10 through 18 Gauge, in the As-Welded Condition, With or Without Backing
焊接状态下 带或不带衬垫的10至18号规格碳钢（M-1 第1组）的保护金属极电弧焊的标准焊接工艺规范
1991-01-01
AWS B2.1.013-91
Standard Welding Procedure Specification for Shielded Metal Arc Welding of Austenitic Stainless Steel, (M-8 or P-8), 10 through 18 Gauge, in the As-Welded Condition, With or Without Backing
焊接状态下10至18号奥氏体不锈钢（M-8或P-8）带或不带衬垫的保护金属极电弧焊的标准焊接工艺规范
1991-01-01
1A1W1S1 Archive Product 37
Standard Welding Procedure Specification for Gas Tungsten Arc Welding Followed by Shielded Metal Arc Welding of Austenitic Stainless Steel (M-8/P-8/S-8, Group 1), 1/8 through 1-1/2 inch Thick, As-Welded Condition
焊接状态下1/8至1-1/2英寸厚的奥氏体不锈钢（M-8/P-8/S-8 第1组）的气体保护钨极电弧焊后的标准焊接工艺规范
2001-10-31
AWS B2.1.001-90
Standard Welding Procedure Specification for Shielded Metal Arc Welding of Carbon Steel, (M-1/P-1, Group 1 or 2), 3/16 through 3/4 inch, in the as-Welded Condition, With Backing
3/16至3/4英寸碳钢（M-1/P-1 第1组或第2组）在焊接状态下带衬垫的保护金属极电弧焊的标准焊接工艺规范
1990-01-01
1A1W1S1 Archive Product 408
STANDARD WELDING PROCEDURE SPECIFICATION (WPS) FOR SHIELDED METAL ARC WELDING OF CARBON STEEL, (M-1/P-1, GROUP 1 OR 2), 3/16 THROUGH 3/4 INCH, IN THE AS WELDED CONDITIONS WITH BACKING
3/16至3/4英寸碳钢（M-1/P-1 第1组或第2组）在带衬垫的焊态条件下的保护金属极电弧焊标准焊接工艺规范（WPS）
1989-12-18
AWS B2.1.014-91
Standard Welding Procedure Specification for Shielded Metal Arc Welding of Carbon Steel to Austenitic Stainless Steel, (M-1 to M-8 or P-8)10 through 18 Gauge, in the As-Welded Condition, With or Without Backing
焊接状态下 带或不带衬垫的碳钢与奥氏体不锈钢（M-1至M-8或P-8）10至18 Gauge的保护金属极电弧焊的标准焊接工艺规范
1991-01-01
AWS B2.1-1-234-2006
Standard Welding Procedure Specification (Swps) for Argon Plus 25% Carbon Dioxide Shielded Flux Cored Arc Welding of Carbon Steel (M-1/P-1/S-1) Groups 1 and 2, 1/8 through 1-1/2 inch Thick, E7XT-X, As-Welded or PWHT Condition, Primarily Pipe Applications
碳钢（M-1/P-1/S-1）1和2组1/8至1-1/2英寸厚E7XT-X焊态或焊后热处理条件下的氩加25%二氧化碳保护药芯焊丝电弧焊标准焊接工艺规范（Swps） 主要用于管道应用
2006-01-01
AWS B2.1-1-235-2006
Standard Welding Procedure Specification (Swps) for Argon Plus 2 Oxygen Shielded Gas Metal Arc Welding of Carbon Steel (M-1/P-1/S-1) Groups 1 and 2, 1/8 through 1-1/2 inch Thick, ER70S-3, Flat Position Only, As Welded or PWHT Condition, Primarily Pipe Applications
碳钢（M-1/P-1/S-1）1组和2组1/8至1-1/2英寸厚ER70S-3 仅平焊位置 焊态或焊后热处理条件 主要用于管道应用的氩加氧保护气体保护金属极电弧焊标准焊接工艺规范（Swps）
2006-01-01
AWS B2.1-1-012-2002(R2013)
Standard Welding Procedure Specification (Swps) for Shielded Metal Arc Welding of Carbon Steel (M-1, P-1, or S-1 to M-1, P-1, or S-1), 10 through 18 Gauge, in the As-Welded Condition, with or without Backing
焊接状态下10至18 Gauge碳钢（M-1、P-1或S-1至M-1、P-1或S-1）带或不带衬垫的保护金属极电弧焊标准焊接工艺规范（Swps）
2002-01-01
1A1W1S1 Archive Product 180
Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding followed by Shielded Metal Arc Welding of Chromium-Molybdenum Steel (M-4/P-4, Group 1 or 2), 1/8 through 1/2 in. Thick, As-Welded Condition, As-Welded Condition, 1/8 through 1-1/2 in. Thick, PWHT Condition, ER80S-B2 and E801
1/8至1/2英寸铬钼钢（M-4/P-4 第1组或第2组）的气体保护钨极电弧焊后的标准焊接工艺规范（WPS） 厚度 焊接状态 焊接状态 1/8至1-1/2英寸 厚度 焊后热处理条件 ER80S-B2和E801
1999-01-01
AWS B2.1-1/8-014-2002(R2013)
Standard Welding Procedure Specification (Swps) for Shielded Metal Arc Welding of Carbon Steel to Austenitic Stainless Steel (M-1 to M-8/P-8/S-8, Group 1), 10 through 18 Gauge, in the As-Welded Condition, with or without Backing
焊接状态下 带或不带衬垫的10至18 Gauge碳钢至奥氏体不锈钢（M-1至M-8/P-8/S-8 第1组）的保护金属极电弧焊标准焊接工艺规范（Swps）
AWS B2.1-5A-226-1999(R2009)
Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding (Consumable Insert Root) followed by Shielded Metal Arc Welding of Chromium-Molybdenum Steel (M-5A/P-5A), 1/8 through 1/2 in. Thick, As-Welded Condition; 1/8 through 1-1/2 in. Thick, PWHT Condition, IN521, ER90S-B3, and E9
1/8至1/2英寸铬钼钢（M-5A/P-5A）的气体保护钨极电弧焊（自耗镶块根部）和金属保护电弧焊的标准焊接工艺规范（SWPS） 厚 如焊接状态；1/8至1-1/2英寸 厚度、焊后热处理条件、IN521、ER90S-B3和E9
1999-12-08
AWS B2.1-5A-224-1999(R2009)
Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding followed by Shielded Metal Arc Welding of Chromium-Molybdenum Steel (M-5A/P-5A), 1/8 through 1/2 in. Thick, As-Welded Condition; 1/8 through 1-1/2 in. Thick, PWHT Condition, ER90S-B3 and E9018-B3, Primarily Pipe Applic
1/8至1/2英寸铬钼钢（M-5A/P-5A）的气体保护钨极电弧焊后的标准焊接工艺规范（SWPS） 厚 如焊接状态；1/8至1-1/2英寸 厚度 焊后热处理条件 ER90S-B3和E9018-B3 主要用于管道应用
1999-12-08
AWS B2.1-1-018-1994
Standard Welding Procedure Specification for Self-Shielded Flux Cored Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, E71T-8, As Welded Condition
1/8至1-1/2英寸厚E71T-8焊态碳钢（M-1/P-1/S-1 第1组或第2组）自保护药芯焊丝电弧焊的标准焊接工艺规范
1994-01-01
AWS B2.1-1-203-2019
Standard Welding Procedure Specification for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 3/4" Thick, E6010 (Vertical Uphill), As-Welded Condition, Primarily Pipe Applications
1/8至3/4“厚E6010（垂直上坡）焊态碳钢（M-1/P-1/S-1 第1组或第2组）的保护金属极电弧焊标准焊接工艺规范 主要用于管道应用
2019-03-01