AWS C5.3-2000
Air Carbon Arc Gouging and Cutting
空气碳弧气刨和切割
2000-01-01
JB/T 7108-1993
碳弧气刨机
Carbon arc air gouging machines
1993-10-08
AWS A5.18/A5.18M-2021
Specification for Carbon Steel Electrodes and Rods for Gas Shielded Arc Welding
气体保护电弧焊用碳钢焊条和焊条规范
2021-01-01
JB/T 8679-2014
炭弧气刨炭棒 物理及使用性能试验方法
Test method for physical-operational performance of air-arc gouging carbon electrodes
2014-05-12
CSA W48.4-95
Solid Carbon Steel Filler Metals for Gas Shielded Arc Welding
气体保护电弧焊用固体碳钢填充金属
1995-01-01
AWS A5.2/A5.2M-2007
Specification for Carbon and Low Alloy Steel Rods for Oxyfuel Gas Welding
氧气焊接用碳素钢和低合金钢棒规范
2007-02-12
CB/T 4122-2011
船舶碳素钢管TIG焊接技术要求
Technical requirements for tungsten inert gas arc welding of marine carbon pipes
2011-06-15
GB/T 43905.2-2024
焊接及相关工艺中烟尘和气体取样的实验室方法 第2部分：电弧焊、切割及气刨中一氧化碳、二氧化碳、一氧化氮、二氧化氮排放速率的测定
Laboratory method for sampling fume and gases in welding and allied processes — Part 2: Determination of the emission rates of carbon monoxide, carbon dioxide, nitrogen monoxide and nitrogen dioxide during arc welding, cutting and gouging
2024-04-25
BS EN ISO 15011-2-2009
Health and safety in welding and allied processes. Laboratory method for sampling fume and gases-Determination of the emission rates of carbon monoxide (CO), carbon dioxide (CO2), nitrogen monoxide (NO) and nitrogen dioxide (NO2) during arc welding, cutting and gouging
焊接和相关工艺的健康和安全 烟雾和气体取样的实验室方法
2009-11-30
ISO 15011-2-2009
Health and safety in welding and allied processes — Laboratory method for sampling fume and gases — Part 2: Determination of the emission rates of carbon monoxide (CO), carbon dioxide (CO2), nitrogen monoxide (NO) and nitrogen dioxide (NO2) during arc welding, cutting and gouging
焊接和相关工艺的健康与安全——烟雾和气体取样的实验室方法第2部分:电弧焊、切割和气刨过程中一氧化碳（CO）、二氧化碳（CO2）、一氧化氮（NO）和二氧化氮（NO2）排放率的测定
2009-10-05
AWS A5.36/A5.36M-2012
Specification for Carbon and Low-Alloy Steel Flux Cored Electrodes for Flux Cored Arc Welding and Metal Cored Electrodes for Gas Metal Arc Welding
药芯电弧焊用碳素钢和低合金钢药芯焊条和气体保护金属极电弧焊用金属药芯焊条规范
2011-12-20
UNE-EN ISO 15011-2-2010
Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 2: Determination of the emission rates of carbon monoxide (CO), carbon dioxide (CO2), nitrogen monoxide (NO) and nitrogen dioxide (NO2) during arc welding, cutting and gouging (ISO 15011-2:2009)
焊接和相关工艺中的健康和安全.烟雾和气体取样的实验室方法.第2部分:电弧焊、切割和气刨过程中一氧化碳（CO）、二氧化碳（CO2）、一氧化氮（NO）和二氧化氮（NO2）排放率的测定（ISO 15011-2-2009）
2010-09-29
NASA SSTD-8070-0015-WELD Rev.C
Gas Tungsten Arc Weld (GTAW) Procedure for Carbon Steel (ASME P-No. 1, Group 1 or 2), Revision (21-01-11)
碳钢钨极气体保护焊（GTAW）程序（ASME P-1 第1或2组） 修订版（21-01-11）
2021-01-01
AWS B2.1-1-232-2006
Standard Welding Procedure Specification (Swps) for Argon Plus 25% Carbon Dioxide Shielded Gas Metal Arc Welding (Short Circuting Transfer Mode) followed by Argon Plus 25% Carbon Dioxide Shielded Flux Cored Arc Welding of Carbon Steel (M-1/P-1/S-1, Groups 1 and 2), 1/8 through 1-1/2 inch Thick, ER70
1/8至1-1/2英寸厚ER70碳钢（M-1/P-1/S-1 第1组和第2组）氩加25%二氧化碳保护气体保护金属弧焊（短路过渡模式）和氩加25%二氧化碳保护药芯焊丝电弧焊的标准焊接工艺规范（Swps）
2006-01-01
1A1W1S1 B2.1.004-90
Standard Welding Procedure Specification for Gas Metal Arc Welding of Carbon Steel (M-1, Group 1), 10 through 18 Gauge, in the As-Welded Condition, With or Without Backing
焊接状态下10至18号规格碳钢（M-1 第1组）带或不带衬垫的气体保护金属极电弧焊的标准焊接工艺规范
1990-01-01
AWS B2.1-1-233-2006
Standard Welding Procedure Specification (Swps) for Argon Plus 25% Carbon Dioxide Shielded Gas Metal Arc Welding (Short Circuting Transfer Mode) followed by Argon Plus 2% Oxygen Shielded Gas Metal Arc Welding (Spray Transfer Mode) of Carbon Steel (M-1/P-1/S-1) Groups 1 and 2, 1/8 through 1-1/2 inch
碳钢（M-1/P-1/S-1）组1和2、1/8至1-1/2英寸的氩加25%二氧化碳气体保护金属极弧焊（短路过渡模式）和氩加2%氧气保护气体保护金属极弧焊（喷射过渡模式）的标准焊接工艺规范（Swps）
2006-01-01
BS ISO 14404-3-2017
Calculation method of carbon dioxide emission intensity from iron and steel production-Steel plant with electric arc furnace (EAF) and coal-based or gas-based direct reduction iron (DRI) facility
钢铁生产中二氧化碳排放强度的计算方法
2017-06-28
AWS B2.1.006-90
Standard Welding Procedure Specification for Gas Metal Arc Welding of Carbon Steel to Austenitic Stainless Steel, (M-1 to M8 or P-8), 10 through 18 Gauge, in the As-Welded Condition, With or Without Backing
焊接状态下10至18号（M-1至M8或P-8） 带或不带衬垫的碳钢与奥氏体不锈钢的气体保护金属极电弧焊标准焊接工艺规范
1990-01-01
1A1W1S1 Archive Product 26
Standard Welding Procedure Specification for Gas Tungsten Arc Welding of Carbon Steel, (M-1/P-1, Group 1 or 2), 3/16 through 7/8 inch, in the As-Welded Condition, With or Without Backing
3/16至7/8英寸碳钢（M-1/P-1 第1组或第2组）在焊接状态下 带或不带衬垫的钨极气体保护焊的标准焊接工艺规范
1990-01-01
AWS B2.1-1-004-2002(R2013)
Standard Welding Procedure Specification (Swps) for Gas Metal Arc Welding (Short Circuiting Transfer Mode) of Carbon Steel (M-1, Group 1), 18 through 10 Gauge, in the As-Welded Condition, with or without Backing
焊接状态下18至10号规格碳钢（M-1 第1组）带或不带衬垫的气体保护金属极电弧焊（短路过渡模式）的标准焊接工艺规范（Swps）
2002-01-01